序號

新編碼

設備名稱

型號

安裝年月

使用車間

位置

設備檢測問題點

要求

1

758-001

數控門式火焰切割機

AG-550

2004.04

結構

G跨北2-4柱

X向主側導軌的水平度和直線度偏差；                                                                                    X向副側導軌的水平度和直線度偏差；                                                         X向主側導軌齒條的銜接間隙部分有偏差；                                                             X向副側導軌齒條的銜接間隙部分有偏差；                                                              X向與Y向導軌垂直度誤差5毫米；                                                                        無自動點火裝置；                                                                                                                                                                        

XY向輸出齒輪更換；                                          龍門架需校正。

2

758-004

火焰切割機

AG-550

2006.05

結構

G跨北4-6柱

X向主側導軌的水平度和直線度偏差；                                                                                    X向副側導軌的水平度和直線度偏差；                                                         X向主側導軌齒條的銜接間隙部分有偏差；                                                             X向副側導軌齒條的銜接間隙部分有偏差；                                                              X向與Y向導軌垂直度誤差3毫米；                                                                        無自動點火裝置；                                                                                                                                                                        

XY向輸出齒輪更換；                                          龍門架需校正。

3

758-009

數控火焰氣割機

ERGOREX-EXA

1990.10

結構

G跨北7-9柱

X向主側導軌的水平度和直線度偏差；                                                                                    X向副側導軌的水平度和直線度偏差；                                                         X向主側導軌齒條的銜接間隙部分有偏差；                                                             X向副側導軌齒條的銜接間隙部分有偏差；                                                              X向與Y向導軌垂直度誤差2毫米；                                                                        無自動點火裝置；                                                                                                                                                                        

XY向輸出齒輪更換；                                          龍門架需校正；                                                 主副導軌直線度超差需矯正；

4

C-008

精細等離子切割機

PG-500

2007.09

結構

H跨北2-5柱

X向主側導軌齒條的銜接間隙部分有偏差；                                                                                                                           X向與Y向導軌垂直度誤差5毫米；                                                                        無自動點火裝置；                                                                                                                                                                        

龍門架需校正；                                                 

5

958-026

數控火焰氣割機

DSCUT-6500

2022.1.18

結構

G跨北9-11柱

X向主側導軌的水平度和直線度偏差；                                                                                    X向副側導軌的水平度和直線度偏差；                                                         X向主側導軌齒條的銜接間隙部分有偏差；                                                             X向副側導軌齒條的銜接間隙部分有偏差；                                                              X向與Y向導軌垂直度誤差2毫米；                                                                        無自動點火裝置；                                                                                                                                                                        

XY向輸出齒輪更換并調整；                                          龍門架需校正；                                                 主副導軌直線度超差需矯正；